‍EDG6000

SmartVU is GAC’s free configuration software for the EDG6000 controllers.  It incorporates a simple user interface for initial configuration as well as added functionality for diagnostic and troubleshooting purposes. Please see the SmartVU User Guide for more information.

• Required:  For engine start, safety, and run-capability.
• Optimization:  For fine-tuning and system calibration.
• Feature:  For optional feature functionality and sensor support.
• Advanced: For troubleshooting, advanced diagnostics etc.

The following is required to run the software:

• A DB-9 female connector is included on the harnessing for communication with SmartVU.  If there is no connection point available, an adapter harness may also be used. 
• An RS-232 port connection is required, since many computers do not have this port use a USB-to-RS-232 converter will be required. GAC recommends GAC part number EAM204.
• For the AFR, ICM, and EDG and IGA typically, a standard pass-through (not null modem) DB-9 F/M cable is required.

To install, unzip the downloaded package to a directory and execute SmartVuECsetup.exe.  Once executed, the installer will guide you through the remainder of the process.

‍

EEG7000

The EEG700 can use one of two tools: 

EEG7000 using GAConfig Tool

EEG7000 using the Interface Tool

Detailed manuals for using EEG7000 with either the GAConfig Tool or the EEG7000 Interface Tool to set parameter values and adjust performance and view results are available. This PC tool offers a single screen access to parameters similar to the SmartVU software. The applications enables you to set the following parameters for your application:

• Required:  For engine start, safety, and run-capability.
• Optimization:  For fine-tuning and system calibration.
• Feature:  For optional feature functionality and sensor support.
• Advanced: For troubleshooting, advanced diagnostics etc.
• Installation and User Manual using  GAConfig Tool
• Installation and User Manual using  EEG7000 Interface Tool

The following is required to run the software:

• A PC with at least Windows 7 or higher and at least one USB port
• An internet connection
• A 14 pin connector (GAC EC1502) or cable harness assembly (CH1520)

‍

EEG7500

EEG7500 speed controller uses the GAConfig Tool to update parameter values on the EEG7500 governor, adjust performance settings, and view results.  This PC tool provides a menu-driven user-friendly interface to update settings, and speed diagnostics and troubleshooting.  The tool also allows you to set up multiple scenarios and save them for use later or for sharing with other sites using the EEG Series. The applications enables you to set the following parameters for your application:

• Required:  For engine start, safety, and run-capability.
• Optimization:  For fine-tuning and system calibration.
• Feature:  For optional feature functionality and sensor support.
• Advanced: For troubleshooting, advanced diagnostics etc.
• Installation and User Manual for the EEG7500

The following is required to run the software:

• A PC with at least Windows 7 or higher and at least one USB port
• An internet connection
• A 14 pin connector (GAC EC1502) or cable harness assembly (CH1520)

‍

‍AFR, ICM, IGA Series

SmartVU is GAC’s free configuration software for the AFR, ICM, and  IGA series controllers.  It incorporates a simple user interface for initial configuration as well as added functionality for diagnostic and troubleshooting purposes. Please see the SmartVU User Guide for more information.

• Required:  For engine start, safety, and run-capability.
• Optimization:  For fine-tuning and system calibration.
• Feature:  For optional feature functionality and sensor support.
• Advanced: For troubleshooting, advanced diagnostics etc.

The following is required to run the software:

• A PC with at least Windows 7 or higher and at least one USB port
• An internet connection
• A DB-9 female connector is included on the harnessing for communication with SmartVU.  If there is no connection point available, an adapter harness may also be used. 
• An RS-232 port connection is required, since many computers do not have this port use a USB-to-RS-232 converter will be required. GAC recommends GAC part number EAM204.
• For the AFR, ICM, and EDG and IGA typically, a standard pass-through (not null modem) DB-9 F/M cable is required.

To install, unzip the downloaded package to a directory and execute SmartVuECsetup.exe.  Once executed, the installer will guide you through the remainder of the process.

‍

SDG Series

The SDG500 Series is designed to regulate engine speed on diesel and gasoline reciprocating engines. See the SmartVU User Guide and contact GAC for more information on the SDG Series.

‍

‍DPG

The DPG is a microprocessor-based digital governing system integrated with an electromechanical actuator in a single pump-mountable housing and designed for BQ series inline fuel injection pumps. It uses the GAC SmartVU Engine Control Software .

‍

General Information

• Determining your COM port